AnyTone AT-588UV Manual de usuario

53RedBlackRegulated power supply (QRP-01)DC power cable with fuse holder (QPL-01)Regulatedpower supply (QRP-01)Ext. Power jackACC terminalCigar-Plug c

63Initial Installation REPLACING FUSESIf the fuse blows, determine the cause, then correct the problem. After the problem is resolved, replace the fus

73SP-01SP-01GroundMicrophone connectorMicrophone [QHM-03]Antenna [QCA-01]External speaker [SP-01]ErrorIUUQXXXRYE[DOInitial Installation External

84NO. KEY )81&7,21Pow(Power) Power on/OffVOL Adjust Volume KeyMain DialChange frequency, memory channel and scan direction etc.FUN/SET Functio

9421NO. KEY )81&7,21Ext. Power JackTerminal for connecting optional cable QCC01 for use with ignition key On/Off function.The radio will auto pow

104NO. KEY )81&7,21UP Increase frequency ,channel number or setting value.DOWN Decrease frequency, channel number or setting value.PTT Press th

115According to practical application,you can set the radio works as Amateur Transceiver mode or Professional Transceiver mode . There are also 2 leve

12In standby, press key or Microphone's key until appear , this indicates current channel in channel mode. Repeat above 6PW

13Basic OperationsTransmitting Tone-PulseTransmitting OPTIONAL SIGNALING Press and hold [PTT] key, then press Microphone [ ] key to transmit current

147Shortcut OperationsSquelch level SetupFrequency/Channel ScanChannel ScanCTCSS/DCS Encode and Decode setupSetting the radio to a tight squelch level

We only do best radio!Nice Housing, Stoutness & Stability, Advanced and Reliable functions, Perfect & Valuable. Approval. AT-

157Shortcut OperationsCTCSS SCANRepeatedly press key until LCD displays and icons ,then hold key for 1S to enter into CTCSS scanning. 2QFH¿QGLQJ

16Press key until LCD displays1.icon, then press key until, LCD displays icon, it indicates keypad lockout function is valid.This wil

17Turn selector knob to choose group you 2.desired. Total:16 group,01-16.7Shortcut OperationsPress3.key to enter into editing of current group,press M

18Press2./ key to choose No.01 menu, LCD displays ”STP--125”Turn selector knob to select the desired frequency channel step.3.Channel step: 5K,6.25K,

198Sending 5-Tone CallPress2./ key to choose No.04 menu, LCD displays "5TON XX","XX"indicates the group in the list.Turn selector

208Turn selector knob to select the desired 3.combinationIf select "SQ",it indicates you can hear the calling from caller when receive a mat

218TX OFF SETUPDisable this function,it is invalid to press PTT,current channel only works in RX mode.Press and hold 1.key for over 2s to enter genera

228Press2./ key to choose No.12 menu, LCD displays "REV—OF".Turn selector knob to select the desired 3.setting. ON:Enable Frequency Re

238menu, LCD displays”D--XXX” XXX is radio's DTMF SELF ID. Press3.NH\WRFRQ¿UPDQGH[LWRadio's 5TONE SELF ID ENQUIRYPress and hold1.key

248 1HOUR:Auto power off after 1h 2HOUR:Auto power off after 2h OFF:Disable Auto power offPress4.NH\WRFRQ¿UPDQGH[LW'HIDXOW

Thank you for choosing this vehicle transceiver, always provides high quality products, And this transc

258menu, LCD displays"LAMP--25"Turn selector knob to select the desired LCD backlight brightness 3.1-32 total 32 level backlight brightness.

268Address list You store desired ID and corresponding ID name in address list.The LCD displays ID corresponding name if radio received ANI calling an

279You can operate the transceiver by keypad or input desired frequency or channel through the QHM-03 microphone (Note:In professional transceiver mod

289Reverse TX/RXTX frequency turns to RX frequency & RX frequency changes to TX frequency. The signaling will also be reversed if CTCSS/DCS signal

299TOT (Time-out timer)The time-out timer limits the amount of transmitting time. When you reach the time limit which has been programmed by your deal

309 HI:High Power MI:Middle Power LOW:Low Power Press number keys to exit and store.3. LCD Backlight In standby status,press 1. , then press LCD di

3110Connect DC power cable with car battery.Connect the optional alarm cable QL-01(A) to the data jack on 1.the front panel as shown. Secure the other

3211This feature will copy the programmed data and parameters in the master unit to slave units. It copies the parameters and memory program settings.

3312Programming Software Installing and Starting (in windows XP system)Double click ”QPS588 setup.exe“, then follow the installing instruction.7KLVVR

3413AT-588DCS encode and decode.VFO frequency 145.00MHz DCS code 023NMemory channel 1.2::! .Output power HIOffset direction. !!!!!!!!!!!!!!Ke

CONTENTS1HZDQG,QQRYDWLYH)HDWXUHV...1Supplied Accessories/Optional Accessories...2Suppl

35146SHFL¿FDWLRQVDUHVXEMHFWWRFKDQJHZLWKRXWQRWLFHGXHWRDGYDQFHPHQWVLQtechnology.GeneralFrequency RangeVHF: 136-174MHz 245-245.9875MH

361567.0 79.7 94.8 110.9 131.8 156.7 171.3 186.2 203.5 229.169.3 82.5 97.4 114.8 136.5 159.8 173.8 189.9 206.5 233.671.9 85.4 100.0 118.8 141.3 162.2

3715                                 

V1.0-10/06

CONTENTSHIGH/MID/LOW Power Selection ...20Band-width Selection ...

11New and Innovative FeaturesAT-588 Mobile Radio has nice housing, stoutness & stability, advanced and reliable functions, perfect & valuable.

22Supplied Accessories/Optional AccessoriesSupplied AccessoriesOptional AccessoriesAfter carefully unpacking the transceiver, identify the items liste

3To install the transceiver, select a safe, convenient location inside your vehicle that minimizes danger to your passengers and yourself while the ve

4Connect the DC power cable to the transceiver's power supply 6.connector.Press WKHFRQQHFWRUV¿UPO\WRJHWKHUXQWLOWKHORFNLQJWDEFOLFNVIf the